Key takeaways
- Compare the best jerky guns and kits for homemade wild game jerky: tube capacities, nozzle sets, barrel materials, cleaning effort and food safety.
As an Amazon Associate we earn from qualifying purchases.
Affiliate Disclosure: This article contains affiliate links. If you buy through a link on this page, we may earn a commission at no extra cost to you.
Sliced whole-muscle jerky only uses part of a deer. The trim, the shoulder offcuts, and the grind pile need a different tool, and that tool is a jerky gun: a trigger-driven tube that extrudes seasoned ground meat into flat strips or round snack sticks of even thickness, so every piece dries at the same rate in the dehydrator or oven. This guide compares five jerky guns and kits sold on Amazon, from a one-pound starter kit with seasoning and cure in the box to a stainless cannon that swallows more than two pounds per load. Each entry lists the tube capacity, the barrel material, the full nozzle set, and what else ships in the box, because those four things decide how a gun behaves on a real processing day.
Two honest warnings apply to the whole category. First, every jerky gun is fiddly to clean. Ground meat creeps past piston washers, packs into nozzle threads, and dries into a film, so the brushes in the box matter. Second, capacity numbers need reading carefully: most guns hold three-quarters of a pound to a pound and a half per load, and the biggest figures sometimes count a spare barrel, not a single fill. The sections below state each capacity as the maker describes it.
1. LEM Products Jerky Cannon — the heavy-duty standard for deer season
The LEM Jerky Cannon, model 468, is the gun most home processors measure the rest against. Its barrel is anodized aluminum, flared at both ends so a log of seasoned grind slides in without catching and the piston seats without a fight. The drive behind it is built for repetition: a heavy-duty plastic piston on a stainless steel rod, pulled by a plastic-coated steel handle. A full tube holds a pound and a half of ground meat, the practical sweet spot — large enough to fill several dehydrator trays per load, small enough that the trigger hand is not wrecked by the third refill.
Two stainless steel nozzles come in the box: a flat nozzle that lays down strips about 1-3/16 inches wide and 3/16 inch thick, and a round nozzle with a half-inch bore for snack sticks. Both attach with a quick turn of the retaining ring. LEM also includes a nylon barrel brush and two packs of Backwoods seasoning, one Original Jerky and one Snack Stick, each sized to season five pounds of meat. The trade-offs are the usual ones for anodized aluminum: the barrel is hand wash only, and meat still works its way around the piston washers, so the brush earns its place. For a hunter turning one or two deer a year into ground jerky, this is the balanced pick.
Specs
- Capacity: 1.5 lb of ground meat per load
- Barrel: Anodized aluminum, flared at both ends
- Drive: Heavy-duty plastic piston, stainless steel rod, plastic-coated steel handle
- Nozzles: 2 stainless steel — flat (1-3/16 in x 3/16 in) and round snack stick (1/2 in ID)
- Included: Nylon barrel brush; 2 packs Backwoods seasoning (Original Jerky and Snack Stick, each seasons 5 lb)
- Care: Barrel hand wash only
- Best for: Regular deer-season batches of strips and sticks
2. Weston Original Jerky Gun Kit — double nozzles for faster tray filling
Weston’s Original Jerky Gun Kit, model 37-0150-W, attacks the slowest part of gun work: laying strips one at a time. Its two stainless steel attachments are both doubles. The double jerky strip nozzle extrudes two flat strips per squeeze, and the double snack stick nozzle forms two round sticks at once, so a pound and a half of grind becomes finished strips in noticeably fewer trigger pulls than a single-nozzle gun. The tube itself is lightweight aluminum holding the same pound and a half as the LEM, driven by an easy-squeeze trigger with a coated steel plunger mechanism.
The kit rounds itself out with the loading gear other brands skip: a stomper for packing the tube and pushing out air pockets, a plastic sausage funnel that lets the gun fill casings as well, and two cleaning brushes sized for the tube and the nozzles. Air pockets are not a cosmetic issue — they leave voids in the strip that dry unevenly — so the stomper is a genuinely useful inclusion. Cleaning follows the category pattern: the removable parts hand wash in hot soapy water, and the handle assembly is not dishwasher safe and should not be immersed. Choose this one when the batch is big and the afternoon is short.
Specs
- Capacity: 1.5 lb of ground meat per load
- Tube: Lightweight aluminum; coated steel trigger and plunger mechanism
- Nozzles: 2 stainless steel doubles — double jerky strip and double snack stick
- Extras: Plastic sausage funnel, stomper, 2 cleaning brushes
- Forms: Flat strips, round sticks, and filled sausage links via the funnel
- Care: Hand wash removable parts; handle assembly not dishwasher safe, do not immerse
- Best for: Larger batches where extrusion speed matters
3. SIGVAL Frontier Jerky Gun — the widest nozzle set in this guide
The SIGVAL Frontier, sold in its Beefy version, ships with more ways to shape meat than any other gun here. Three stainless steel jerky nozzles cover the strip family: a flat nozzle laying strips an eighth of an inch thick and an inch and a half wide, a double flat nozzle at a quarter inch thick for two narrower strips per pull, and a round nozzle that forms sticks five-eighths of an inch across. Behind those sit three tapered sausage tips, so the same gun that makes jerky on Saturday can fill small sausage casings on Sunday. The barrel is anodized aluminum with a pound and a half capacity, and the handles are die-cast metal rather than plastic, which is the part of a jerky gun that flexes and eventually cracks on cheaper tools.
Two cleaning brushes are included, and SIGVAL notes the stainless tips can go in the dishwasher, which trims the worst part of the cleanup even though the barrel and piston still want hand washing. Thickness is the quiet advantage of this set: the eighth-inch flat strips dry fast and crisp, the quarter-inch doubles stay chewier, and having both in one box means the texture decision happens at the nozzle rack, not the checkout. If you make sticks and strips in roughly equal measure and want one gun to cover both, this is the flexible pick.
Specs
- Capacity: 1.5 lb of ground meat per load
- Barrel: Anodized aluminum; die-cast metal handles
- Jerky nozzles: 3 stainless steel — flat (1/8 in thick x 1-1/2 in wide), double flat (1/4 in x 1-1/8 in), round stick (5/8 in)
- Sausage tips: 3 tapered nozzles included
- Included: 2 cleaning brushes
- Care: Stainless tips dishwasher safe per the maker; barrel and piston hand wash
- Best for: Makers who split time between strips, sticks, and small sausages
4. MTOGALT Stainless Steel Jerky Gun Kit — the big all-stainless cannon
Most jerky guns mix materials — an aluminum tube here, a plastic piston there. This MTOGALT kit is built from 304 stainless steel throughout, barrel included, and it is also the largest gun in this guide at a 2.1-pound tube capacity. Stainless changes the ownership math in two ways: it shrugs off the dents and coating wear that anodized aluminum collects, and it tolerates a thorough hot scrub without hand-wash-only warnings on the barrel. For someone processing several deer, a hog, or a bulk buy of ground beef in one session, the extra half pound per load over the standard guns adds up to real time saved across a ten-pound batch.
Five stainless steel nozzles cover flat strips, round sticks, and sausage work, a stainless meat pusher packs the tube, and five cleaning brushes in assorted sizes handle the barrel, the nozzles, and the threads. What the box does not include is any seasoning or cure, so a first-time buyer needs to add those separately before processing day. The honest downside is effort: a fuller, heavier tube of dense grind takes more trigger force per squeeze, and on a long batch your forearm will know it. This is the pick for high-volume makers who would rather reload less often and clean aggressively.
Specs
- Capacity: 2.1 lb of ground meat per load
- Construction: 304 stainless steel barrel and fittings
- Nozzles: 5 stainless steel nozzles for strips, sticks, and sausage
- Included: Stainless steel meat pusher, 5 cleaning brushes, instruction manual
- Seasoning/cure: None included
- Care: Stainless parts scrub clean in hot soapy water; brushes included for barrel and threads
- Best for: High-volume batches and buyers who prefer all-stainless construction
5. Nesco BJX-5 Jerky Works Jumbo Kit — the starter kit with seasoning and cure
The Nesco BJX-5 is the only entry here designed to take a complete beginner from a sealed box to a first dried batch. The gun itself is the simple end of the category: a see-through plastic meat chamber that holds one pound, so you can watch the level fall and spot air pockets before they reach the nozzle, driven by a stainless steel trigger and ratchet bar. Three attachments cover the core shapes — a wide strip nozzle, a dual strip nozzle that forms two strips at once, and a round stick nozzle.
What makes it a kit rather than just a gun is what else is in the carton: two packs of Nesco’s Original flavor seasoning and two packs of cure, enough for up to four pounds of meat, with the seasoning gluten free and made in the USA. That matters for a first batch because ground-meat jerky should be made with cure, and a beginner who has to source it separately often skips it. The limits are equally clear: a one-pound tube means frequent refills on anything beyond a small batch, and a plastic chamber will not take the years of squeezing the aluminum and stainless guns above are built for. As a low-commitment way to find out whether ground jerky belongs in your processing routine, it is the right shape of tool.
Specs
- Capacity: 1 lb of ground meat per load
- Chamber: See-through plastic; stainless steel trigger and ratchet bar
- Attachments: 3 — wide strip, dual strip, and round stick
- Included: 2 packs Original seasoning and 2 packs cure, enough for up to 4 lb of meat
- Seasoning: Gluten free, made in the USA
- Dimensions: 11.75 x 3.25 x 6.5 in
- Best for: First-time makers and small test batches
How to Choose
Start with capacity, because it decides how a processing day feels. A one-pound tube suits test batches and small grinds; the pound-and-a-half class is the home standard and fills several trays per load; a two-pound-plus stainless cannon earns its keep only when batches regularly run past five pounds, because every extra ounce in the tube is extra trigger force on every squeeze. Whatever the headline figure, check whether it describes one tube or a tube plus a spare barrel — those are not the same thing mid-batch.
Next, match material to temperament. Plastic chambers are light and cheap and fine for occasional use. Anodized aluminum is the durable middle ground, with the caveat that barrels are hand wash only. Stainless steel costs and weighs more but tolerates hard scrubbing and years of service. Then count nozzles against your actual recipes: a flat and a round cover most makers; double nozzles halve extrusion time on big batches; sausage tips and funnels only matter if casings are genuinely on your list. Finally, look at what is in the box. Brushes are not accessories — they are how the gun gets clean — and kits that include seasoning and cure, like the LEM Cannon and the Nesco, remove the two items beginners most often forget.
However you choose, treat food safety as part of the tool decision. Ground meat is riskier than whole muscle because grinding distributes surface bacteria through the batch, so published USDA guidance for home jerky calls for using cure and for heating ground meat to an internal temperature of 160 degrees Fahrenheit — a step many dehydrators running at 145 to 155 degrees do not reach on their own, which is why oven finishing or pre-heating steps appear in the manufacturers’ own instructions. Keep the grind cold until it goes in the tube, refrigerate formed strips if drying will not start right away, and do not let a new gun talk you out of the cure packet.
FAQ
Do I need cure for ground-meat jerky?
Yes, plan on it. Cure is a standard part of published ground-jerky practice because ground meat carries more risk than sliced whole muscle, and it also gives sticks and strips their characteristic colour and flavour. Two of the kits in this guide, the LEM Cannon and the Nesco BJX-5, include cure or cure-containing seasoning; with the others, add a curing salt blend measured for your batch size and follow its directions rather than estimating.
How much jerky does one load of a jerky gun make?
A pound and a half of ground meat — the standard tube size here — comes back as roughly half a pound of finished jerky, since ground meat loses about two-thirds of its weight as water during drying. A five-pound grind therefore means three to four refills of a standard gun and produces around a pound and a half to two pounds of jerky.
Are jerky guns really hard to clean?
They are the most cleaning-intensive tool in the processing kit. Meat works past the piston washers and into the nozzle threads, and it dries fast. The routine that works is immediate: strip the gun down as soon as the last strip is laid, soak the tube and nozzles, run the included brushes through every bore, and wash the piston washers individually. Guns with more, better-sized brushes — and stainless parts that tolerate hot water — make this noticeably less miserable.
Can a jerky gun fill sausage casings too?
Some can, in a limited way. The Weston kit includes a sausage funnel and the SIGVAL includes three tapered sausage tips, and both will fill small casings with a soft grind. A jerky gun is not a substitute for a dedicated stuffer on a big sausage day, though: the tube is small, the pressure is uneven compared with a crank stuffer, and reloading every pound and a half gets old fast.
Why do my strips dry unevenly?
Usually the extrusion, not the dryer. Strips laid at different thicknesses dry at different rates, which is exactly the problem a gun exists to solve — so check for air pockets in the tube, inconsistent trigger pressure, or a nozzle partly blocked with gristle. Packing the tube firmly with a stomper or pusher, and keeping a steady squeeze, produces the even thickness that dries evenly.
Conclusion
For most hunters making ground venison jerky, the LEM Jerky Cannon is the reference point: a pound and a half of capacity, an anodized barrel, the two nozzles that matter, and seasoning in the box. The Weston matches that capacity and adds double nozzles and a stomper for faster work, while the SIGVAL Frontier trades blows with both and wins on sheer nozzle variety. The MTOGALT is the volume and durability play — all stainless, the biggest tube here, nothing else in the box — and the Nesco BJX-5 is the honest starter, a smaller plastic gun bundled with the seasoning and cure a first batch needs. Pick by batch size first, material second, and keep the cure and the brushes as close to the gun as the nozzles.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!