Key takeaways
- Compare five drill bit sets for wood, metal and home projects, from titanium and black oxide everyday sets to M35 and M42 cobalt for harder metals.
As an Amazon Associate we earn from qualifying purchases.
A good drill bit set earns its place in the toolbox by covering the sizes a household actually reaches for, starting holes without skating across the surface, and holding an edge long enough that the small bits do not need constant replacing. The five sets below were chosen because each one fills a clear role: two coated general-purpose sets for everyday wood, plastic and mild metal work, an impact-rated hex-shank set for drill and driver users, and two cobalt sets for harder metals such as stainless steel and cast iron. Every set here is built around twist bits in an indexed storage case, and every size range, coating and shank detail is stated in the maker’s own terms.
How to Choose a Drill Bit Set
Start with the material you drill most. Plain high-speed steel bits with a black oxide finish handle wood, plastic and light-gauge metal well and are the least demanding on the wallet. Titanium nitride coated bits add a hard surface layer that reduces friction at the cutting edge, which suits mixed household work in wood and metal. Cobalt alloy bits are the step up for hardened steel, stainless and cast iron, because the cobalt runs through the whole bit rather than sitting on the surface.
Understand what a coating can and cannot do. A titanium nitride or black oxide coating lives on the surface of the bit, and it wears away at the cutting edge first, exactly where the work happens. Once that edge coating is gone, the bit behaves like the steel underneath it, and resharpening removes more of the coating. Cobalt is different: because the alloy is mixed through the bit, a cobalt bit keeps its heat resistance after sharpening. The trade-off is that cobalt bits are more brittle than standard high-speed steel, so they punish side loading and wobbling in a hand drill.
Check the size range, not just the piece count. A 29-piece set in 1/64 inch steps gives one of every size from 1/16 to 1/2 inch, which matters when a hole has to match a specific bolt or tap size. Smaller sets often double up on the smallest, most-used sizes instead, which is practical because small bits break most often. Either approach is valid; the right one depends on whether the work is fastener-driven or general purpose.
Match the shank to the tool. Round shanks belong in a keyed or keyless chuck on a drill or drill press. Three-flat shanks resist spinning in the chuck under load. A 1/4 inch hex shank drops straight into an impact driver for quick changes, which is convenient on site work, but the hex section is a weak point if a bit binds and snaps.
Mind the point style. A 135-degree split point starts on contact with less wandering on metal and usually removes the need for a center punch on flat stock. Standard 118-degree points are common on general-purpose bits and work fine in wood, where the grain guides the bit.
1. DEWALT Titanium Nitride Coated Pilot Point Drill Bit Set, 21-Piece (DW1361)
This is the everyday set for a household that drills wood, plastic and metal with the same kit. The Pilot Point tip design starts on contact, which keeps holes placed accurately on metal and painted surfaces where a standard point tends to skate. The titanium nitride coating gives the cutting edges a harder working surface than a plain bit, and the set doubles up on the five smallest sizes, acknowledging that the thin bits are the ones that snap. Larger bits carry a no-spin shank design so the chuck grips instead of polishing the shank when a hole gets tight. It is a sensible first set for general home projects, with the understanding that the coating will wear at the edges over time and that hardened stainless work belongs to the cobalt sets below.
Specs
- Pieces: 21
- Bit types: Twist drill bits with Pilot Point tips
- Size range: 1/16 in to 1/2 in, with duplicate bits in the five smallest sizes
- Material and coating: Titanium nitride coated, in the maker’s wording
- Shank: Round shank on the smallest bits; no-spin hex shank on 3/16 in and larger bits
- Case: Plastic storage case
2. DEWALT Black Oxide Drill Bit Set, 20-Piece (DW1177)
The DW1177 is the straightforward black oxide option: twenty high-speed steel twist bits with a 135-degree split point, sized from 1/16 to 1/2 inch. Black oxide is a surface treatment rather than a hard coating, and its real jobs are resisting rust in storage and reducing friction slightly as the bit turns. That makes this set a practical choice for wood, plastic and light metal around the house and campsite workshop, where most holes are in timber, brackets and sheet material rather than hardened steel. The split point helps the bit bite without wandering, and the full spread of sizes covers the fasteners used in most home projects. Buyers should expect black oxide bits to dull faster in sustained metal drilling than titanium coated or cobalt bits; that is the honest trade-off of the finish, not a defect.
Specs
- Pieces: 20
- Bit types: Twist drill bits with 135-degree split point
- Size range: 1/16 in to 1/2 in
- Material and coating: High-speed steel with black oxide coating, in the maker’s wording
- Shank: Round shank
- Case: Plastic storage case
3. Makita Impact Gold Titanium Drill Bit Set, 14-Piece (B-65399)
The Makita B-65399 is built for impact drivers. All fourteen bits sit on 1/4 inch hex shanks, so they lock into an impact driver’s quick-release collet and also work in a standard drill chuck. The titanium nitride coating is the maker’s Impact Gold finish, and the 135-degree split point keeps starts accurate on metal. The size range runs from 1/16 to 1/2 inch, which means fewer, widely spaced sizes than a 29-piece index; this set is about speed and convenience on framing, deck and assembly work rather than complete size coverage. Makita rates the set for wood, plastic and metal. One honest caution applies to every hex-shank drill bit: if a bit binds and breaks, it usually breaks at the hex, and the whole bit is done, whereas a snapped round-shank bit sometimes leaves enough length to keep using.
Specs
- Pieces: 14
- Bit types: Twist drill bits with 135-degree split point, impact rated
- Size range: 1/16 in to 1/2 in
- Material and coating: Titanium nitride coating, in the maker’s wording
- Shank: 1/4 in hex shank
- Case: Plastic storage case
4. Bosch Cobalt M42 Drill Bit Set, 14-Piece (CO14B)
When the work shifts to stainless steel, cast iron and other hard metals, cobalt is the correct answer, and the Bosch CO14B is the compact way to get it. Bosch builds these bits from Cobalt M42 alloy, which the maker describes as an upgraded cobalt alloy with high heat resistance and a hardened surface, aimed at stainless steel, cast iron, titanium and light-gauge metal. The three-flat shank keeps the bits from spinning in the chuck under the heavy torque that metal drilling demands, and the split point tip starts cleanly. Fourteen pieces cover 1/16 to 3/8 inch, so there is no 1/2 inch bit here; this is a hard-metal set to pair with a general-purpose set, not a replacement for one. Cobalt’s brittleness is the trade-off: keep the drill straight, use cutting oil on steel, and let the bit cut at its own pace.
Specs
- Pieces: 14
- Bit types: Twist drill bits with split point tip
- Size range: 1/16 in to 3/8 in
- Material and coating: Cobalt M42 alloy, in the maker’s wording
- Shank: Three-flat shank
- Case: Included storage case
5. IRWIN Cobalt Drill Bit Set, 29-Piece (3018002)
The IRWIN 3018002 is the full-coverage cobalt option. Twenty-nine bits step from 1/16 to 1/2 inch in 1/64 inch increments, so the exact size for a clearance hole, a tap drill or a dowel is almost always in the case. IRWIN makes the bits from M35 Cobalt Alloy Steel, in the maker’s wording, with a 135-degree split point for accurate starts, and houses them in a metal index case that stands up to workshop life better than thin plastic. This is the set for a home workshop that regularly drills steel, works on trailer and gate hardware, or maintains farm and camp equipment. The same cobalt guidance applies: these bits hold an edge in hard, abrasive metal far longer than coated bits, but they are brittle, so a drill press or a steady hand and cutting lubricant will get the best life out of them.
Specs
- Pieces: 29
- Bit types: Twist drill bits with 135-degree split point
- Size range: 1/16 in to 1/2 in in 1/64 in increments
- Material and coating: M35 Cobalt Alloy Steel, in the maker’s wording
- Shank: Round shank
- Case: Metal index case
Which Set Fits Which Job
For a single set that covers most household drilling in wood, plastic and mild steel, the DEWALT DW1361 or DW1177 does the job, with the titanium nitride set offering the harder edge surface. For impact driver owners who want one holder for driving and drilling, the Makita B-65399 is the fit. For stainless fasteners, hardened brackets and cast iron, skip the coated sets and go straight to cobalt: the Bosch CO14B for the common smaller sizes, or the IRWIN 3018002 when full 1/64 inch coverage up to 1/2 inch matters. Many workshops end up with one general-purpose set and one cobalt set, and that pairing covers nearly everything a home project can present.
Safety and Recall Check
Drill bits are simple tools, but a few habits matter. Wear eye protection whenever drilling metal, because chips and a snapping small bit both travel fast. Clamp small workpieces instead of holding them by hand, keep loose clothing and gloves away from the spinning chuck, and let a hot bit cool before handling it after drilling metal. Cobalt and coated bits alike should be run at lower speeds in steel with cutting oil to control heat.
For recall status, the SaferProducts.gov database run by the U.S. Consumer Product Safety Commission was queried on 2026-11-21 using the product name “drill bit”. The query returned a single record: a 2006 safety alert (recall 06185) concerning Vermont American brand 13-inch-long masonry drill bits sold from 2001 to 2004, whose packaging lacked a required safety warning label. None of the five sets in this guide is named in that record, and none of the five sets appears in any recall returned by the query. The Vermont American masonry bits are a different product type, sold as individual long masonry bits rather than twist bit sets, and are not connected to any pick here, including the Bosch CO14B, which is a cobalt twist bit set of current production.
Affiliate Disclosure
This article contains affiliate links. If you buy through a link on this page, the site may earn a commission at no additional cost to you. Products are selected on their published specifications and suitability for the jobs described, and specifications are taken from the makers’ own listings.
More from Amazon
Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.
Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.
Start a Prime free trialA Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.
See Prime for Young AdultsAudiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.
Try Audible freeAd-free music streaming. Eligible new subscribers can start with a free trial.
Try Music Unlimited freeAs an Amazon Associate we earn from qualifying purchases.






Write Your Review
No reviews yet. Be the first to share your experience!