Updated Nov 22, 2026· 9 min read

Key takeaways

  • Compare the best harmonic balancer pullers for crankshaft work, from bolt-grip yoke kits to LS jaw pullers, with bolt patterns and crank protection tips.

As an Amazon Associate we earn from qualifying purchases.

A harmonic balancer is press-fitted onto the crankshaft snout, keyed so it cannot slip, and held by a single large center bolt. Getting it off again — for a front crank seal, a timing set, or an oil pump — is not a pry-bar job. The correct tool is a harmonic balancer puller: either a bolt-grip yoke puller that threads bolts into the tapped holes in the balancer hub and draws it straight off with a center forcing screw, or a jaw-style puller that grips the hub spokes of balancers that have no tapped holes at all, as on most GM LS engines.

Our top pick: OEMTOOLS 25053 Heavy Duty Harmonic Balancer Puller Set. Runner-up: Thorstone 46-Piece Harmonic Balancer Puller Set.

Two rules govern every removal. First, never pull on the outer ring. That ring is bonded to the hub through rubber elastomer; a puller hooked over it can tear the bond, ruin the balancer, and leave the hub still stuck on the crank. Force must go through the hub — by bolts threaded into the hub face, or by jaws seated on the hub spokes. Second, protect the crankshaft threads. The forcing screw must never bear bare inside the threaded crank bolt hole; the kit’s forcing rod or centering adapter spreads the load on the end of the crank snout. Running the screw tip straight into the hole can mushroom the first threads and turn a seal job into thread repair.

This guide covers only balancer puller kits — not generic jaw gear pullers (a separate guide) and not balancer installers, which are a different tool mentioned here only as a guide boundary.

Before ordering, identify the balancer family. Hubs with tapped holes take a bolt-grip yoke kit containing the exact bolt thread — common patterns include 3/8-16, 3/8-24, 5/16-18, 1/4-28, M8 x 1.25, and M10 x 1.5. Hubs without tapped holes, including GM LS and many Chrysler, Jeep, and Dodge dampers, need a three-jaw or clip-in puller plus forcing rods in different lengths. The five kits below split across both families.

Affiliate Disclosure: This article contains affiliate links. If you buy through them, we may earn a commission at no extra cost to you.

1. OEMTOOLS 25053 Heavy Duty Harmonic Balancer Puller Set — The Classic Bolt-Grip Yoke

The 25053 is the traditional answer for balancers with tapped holes: a four-slot yoke, a center forcing screw, and puller bolts in the threads older domestic V6 and V8 balancers actually use. The four slots allow either two-bolt or three-bolt applications, so one yoke covers balancers drilled in either pattern. Construction is heat-treated alloy steel, which matters because the yoke and screw see the full breakaway load of a balancer that may have been seated for decades.

The bolt assortment is short and focused: 3/8-24, 5/16-18, 3/8-16, and M8 x 1.25 x 80 mm, covering a broad range of bolt circle diameters on balancers with tapped holes. It is not a universal metric set — a balancer using M10 bolts is outside this kit, and the Thorstone set below is the better match there. Within its coverage, the appeal is simplicity: few parts, nothing articulated to misalign, and all force through the hub. At 2.3 pounds, it is also the easiest kit here to store.

Specs

    • Type: Bolt-grip yoke puller for balancers with tapped holes
    • Yoke: 4-slot yoke for 2-bolt or 3-bolt applications
    • Included bolts: 3/8-24, 5/16-18, 3/8-16, M8 x 1.25 x 80 mm
    • Material: Heat-treated alloy steel
    • Weight: 2.3 lb
    • Package size: 10 x 8 x 1.5 in
    • Model: OEMTOOLS 25053

    2. Thorstone 46-Piece Harmonic Balancer Puller Set — Widest Bolt Coverage in a Yoke Kit

    Where the 25053 keeps its bolt list short, the Thorstone 46-piece set goes wide: 30 bolts in SAE and metric threads, a steel four-slot yoke, a 5-inch pressure screw, centering adapters, and a flat shaft adapter, all in a blow-molded carrying case. The yoke handles two- or three-hole applications, and the set is listed for harmonic balancers, flywheels, crankshaft pulleys, and steering wheels on cars, trucks, SUVs, and small-engine vehicles.

    The bolt list is the reason to choose it. Alongside the SAE sizes — 3/8-24, 3/8-16, 5/16-18, and 1/4-28 in several lengths — it adds M8 x 1.25 bolts in 45 mm, 65 mm, and 90 mm lengths and M10 x 1.5 bolts at 35 mm, plus 14 washers. That metric depth is what many import and later domestic balancers require, and three lengths of the common M8 bolt matter because hub depth varies enough that a single length either bottoms out or barely engages.

    Thread each bolt fully into the hub by hand, and seat all bolts in a three-bolt pattern to the same depth so the yoke sits parallel to the balancer face — a cocked yoke concentrates load on one bolt and can snap it. The pressure screw’s floating swivel tip is listed by the maker as preventing damage to shaft ends. All components are heat-treated carbon steel with an oxide finish.

    Specs

      • Type: Bolt-grip yoke puller, 46 pieces
      • Yoke: Steel, 4-slot, for 2-hole or 3-hole applications
      • Pressure screw: 5 in, 3/4-16 thread, floating swivel tip
      • Bolts: 30 bolts including 3/8-24, 3/8-16, 5/16-18, 1/4-28, M8 x 1.25 (45/65/90 mm), M10 x 1.5 (35 mm)
      • Adapters: 2 centering adapters, 1 flat shaft adapter; 14 washers
      • Material: Heat-treated carbon steel, oxide finish
      • Weight: 5.04 lb; case included
      • Model: Thorstone 65575

      3. OEMTOOLS 25090 Harmonic Balancer Puller Kit — Spring-Loaded Jaws for Pressed-On Balancers

      Many late-model balancers have no tapped holes to bolt into, and for those engines the puller has to grip the hub itself. The OEMTOOLS 25090 is an adjustable three-jaw puller built for that job, listed for GM, Ford, Chrysler, and Mitsubishi vehicles and designed to work in tight engine compartments without removing the radiator. Its distinguishing feature is spring-loaded jaws: the springs hold the legs in position on the balancer during setup, freeing a hand for the wrench in a crowded engine bay.

      The six-piece set adds four forcing rods of 4, 5-13/32, 6-1/2, and 7-13/32 inches. After the crank bolt comes out, a rod of the correct length drops into the crank bolt hole and gives the forcing screw a centered surface to push against, so its tip never enters or damages the crank threads. Choosing a rod length that leaves the screw well engaged without bottoming out is the central setup step on every jaw kit here. The screw accepts a 3/8-inch square drive. Jaws must seat on the hub spokes — never the outer ring — with full tip contact, because a jaw riding on a spoke edge can slip under load. The kit weighs 3.64 pounds.

      Specs

        • Type: Adjustable 3-jaw puller for pressed-on balancers without tapped holes
        • Jaws: 3, spring-loaded for position retention
        • Forcing rods: 4 rods — 4, 5-13/32, 6-1/2, and 7-13/32 in
        • Forcing screw drive: 3/8 in square drive
        • Listed applications: GM, Ford, Chrysler, Mitsubishi late-model vehicles
        • Pieces: 6
        • Material: Steel
        • Weight: 3.64 lb
        • Model: OEMTOOLS 25090

        4. ARES 71002 Harmonic Balancer Puller Kit — Dual-Drive Screw and a Proper Case

        The ARES 71002 covers the same pressed-on balancer family as the 25090 but makes different choices in two places: the forcing screw and the storage. The screw is dual-drive — a 3/8-inch square drive for a ratchet and a 3/4-inch hex head for a wrench or socket — so the driver can switch tools as the breakaway load rises and clearance changes. Two forcing screws are listed among the contents alongside the three-jaw puller, four forcing rods, and a storage case.

        ARES lists applications as Chrysler, GM, Mitsubishi, Cadillac, and Oldsmobile vehicles, for tight compartments without radiator removal. The jaws use a position-retention design, and construction is steel with a black oxide finish.

        Follow the manual’s rod guidance literally: measure the crank bolt hole depth, then pick the rod that lets the screw engage fully without bottoming out early, and avoid an over-long rod, which can keep the puller from seating or bend under pressure. ARES does not publish individual rod lengths in its listing data, so buyers needing a specific length should check before the engine is apart. The kit weighs 3.43 pounds.

        Specs

          • Type: Adjustable 3-jaw puller for pressed-on balancers
          • Contents: 3-jaw puller, 4 forcing rods, 2 forcing screws, storage case
          • Forcing screw drives: 3/8 in square drive and 3/4 in hex
          • Listed applications: Chrysler, GM, Mitsubishi, Cadillac, Oldsmobile
          • Material: Steel, black oxide finish
          • Weight: 3.43 lb
          • Package size: 9.17 x 7.09 x 2.05 in
          • Model: ARES 71002

          5. OEMTOOLS 25264 GM Harmonic Balancer Puller — The LS Specialist

          LS balancers defeat both generic jaw pullers and bolt-grip yokes: the GM LS damper has no tapped holes, its hub sits deep, and clearance to the radiator is tight. The OEMTOOLS 25264 is built specifically for that geometry. Its clip-in design grips the balancer without bolting into it, and the maker lists it for GM LS engines including the 5.3L, 5.7 LS1, 6.0 LS2, and 6.2 LS3, as well as Chrysler, Jeep, and Dodge engines including the 3.5L V6, 4.7L V8, and 6.1L V8. It is designed to remove the balancer without removing the radiator.

          The 25264 is a single piece with its necessary bolts and adapters, at 3.35 pounds. That specialization cuts both ways: it is not the tool for earlier GM engines whose balancers have threaded holes — those take the yoke kits above — and truck-pulley and later Ford Coyote-style dampers fall outside its stated applications. Confirm the exact engine against the maker’s list before ordering, because an LS puller bought for a threaded-hole balancer has nothing to clip to. Grip is on the hub, force goes to the crank end, and steady screw pressure walks the balancer off its press fit. The maker backs it with a limited lifetime warranty.

          Specs

            • Type: Clip-in jaw puller for balancers without tapped holes
            • Listed applications: GM LS 5.3L, 5.7 LS1, 6.0 LS2, 6.2 LS3; Chrysler/Jeep/Dodge 3.5L V6, 4.7L V8, 6.1L V8
            • Design: Clip-in grip, no radiator removal required per maker
            • Pieces: 1 (puller with bolts and adapters)
            • Weight: 3.35 lb
            • Warranty: OEMTOOLS limited lifetime
            • Model: OEMTOOLS 25264

            Buying Guide: Matching the Puller to the Balancer

            Start with the balancer face, not the engine badge. If the hub has two or three tapped holes, a bolt-grip yoke kit is the correct and safest design, and the only remaining question is bolt coverage: confirm the kit contains the thread cut into those holes, in a length that engages fully without bottoming. The OEMTOOLS 25053 covers the common older SAE patterns plus M8; the Thorstone set adds M10 and multiple M8 lengths. If the hub has no tapped holes, no yoke kit will work — the choice narrows to general-purpose three-jaw designs like the OEMTOOLS 25090 and ARES 71002, or the LS-dedicated OEMTOOLS 25264.

            Whatever the family, keep force on the hub: seat jaws on spokes or the inner hub, thread bolts into hub holes, and if neither is possible, that balancer needs its factory-specified tool rather than improvisation. Protect the crank by using the kit’s forcing rod, centering adapter, or swivel tip, matched to hole depth before loading. Lubricate the screw threads, load steadily, and keep the puller parallel to the balancer face so it walks off straight.

            Plan the reinstall separately: none of these pullers installs a balancer, and the center bolt alone should not draw one on. A CPSC SaferProducts check for balancer pullers and pulley pullers at the time of writing returned no matching recalls for the kits listed.

            FAQ

            Can a regular three-jaw gear puller remove a harmonic balancer?
            It is the wrong tool for most balancers: its jaws hook the outer ring, which can separate under load. Use a bolt-grip yoke on balancers with tapped holes, or a hub-gripping jaw puller on balancers without them.

            How are the balancer threads protected during a pull?
            By the kit’s forcing rod or centering adapter, which gives the screw a centered surface to push against and keeps its tip out of the crank threads.

            Does an LS engine need a special puller?
            Yes. LS balancers have no tapped holes, so they require a jaw or clip-in puller made for that hub, such as the OEMTOOLS 25264.

            Can these kits reinstall the balancer?
            No. They only remove. Reinstalling requires a dedicated balancer installer with a threaded draw rod and thrust bearing; do not draw a balancer on with its center bolt or strike it with a hammer.

            C
            Camping Spots Editorial Team
            We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
            Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
            Best Harmonic Balancer Pullers for Crankshaft WorkCheck price on Amazon

            More from Amazon

            Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

            Amazon Prime

            Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

            Start a Prime free trial
            Prime for Young Adults

            A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

            See Prime for Young Adults
            Audible

            Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

            Try Audible free
            Amazon Music Unlimited

            Ad-free music streaming. Eligible new subscribers can start with a free trial.

            Try Music Unlimited free

            As an Amazon Associate we earn from qualifying purchases.