Updated Nov 22, 2026· 11 min read

Key takeaways

  • Compare the best scope covers and lens caps for hunting rifle scopes, with exact flip-cap size ranges, neoprene coat fit, materials and measuring tips.

As an Amazon Associate we earn from qualifying purchases.

A hunting scope spends most of its life being carried, not aimed. It rides in a truck rack, knocks against pack frames, drags through wet brush, and sits in a case where zippers and loose gear rub against the glass. Scope covers exist for those hours, in three distinct families: flip-up caps that stay mounted on the scope and open with a thumb, one-piece bikini covers that stretch over both lenses at once, and full neoprene coats that wrap the entire scope body. The five products below cover all three families, from an exact-fit flip cap to a padded coat for a long scope in a soft case.

Our top pick: Butler Creek Multiflex Flip-Open Objective Scope Cover, Size 25-26-27. Runner-up: Vortex Optics Defender Flip Cap.

Fit is the whole decision, and it is decided by one measurement: the outside diameter of the objective bell and the eyepiece housing. That number is not the lens size printed in the scope’s name. Two scopes both sold as 40mm objectives can have different bell diameters, because housing design varies by maker. Every size figure in this article is an outside diameter or a scope length for that reason, and measuring with calipers before ordering is what separates a cover that seals from one that pops off in the field. One honesty note applies to every product here: a cover keeps rain, dust, and brush off the outside of the glass. It does not stop fogging caused by temperature change, because that moisture forms when a cold scope meets warm air, and no cap changes that.

Affiliate Disclosure: This article contains affiliate links. If you purchase through them, this site may earn a commission at no additional cost to you.

1. Butler Creek Multiflex Flip-Open Objective Scope Cover, Size 25-26-27 — The Exact-Fit Standard

The Flip-Open line is the cap most hunting rifles end up wearing, and the Multiflex version solves its one inconvenience. A standard Flip-Open cap is a rigid collar made in a single numbered size, so a bell that falls between sizes forces a compromise. The Multiflex collar is flexible, and one cover spans three consecutive sizes — this listing covers sizes 25, 26, and 27, which correspond to objective bells measuring 1.800 to 1.840 inches (45.7 to 46.7 mm) across the outside. That small window of flex absorbs the minor differences between scope models whose bells are nominally the same size.

The cap itself is built around a silent spring hinge and a thumb tab, so it opens without a snap or click that carries in still woods. The friction mount and the airtight semi O-ring seal hold it on the bell and keep dust and moisture off the lens, and the design is ambidextrous, opening the same way regardless of which side the shooter works from. Butler Creek tests the Flip-Open design across a working range from -40°F to 120°F, which covers any hunting season. Like all flip caps, it is sold one end at a time: objective and eyepiece caps are separate listings with different size runs, so each end of the scope gets measured on its own.

Specs

  • Type: flip-open objective lens cap, sold individually
  • Fit: objective bell outside diameter 1.800–1.840 in (45.7–46.7 mm); spans maker sizes 25, 26, and 27
  • Model: Multiflex 32527
  • Mount and seal: friction mount with airtight semi O-ring seal
  • Hinge: silent spring hinge, ambidextrous, thumb-tab opening
  • Working temperature range: -40°F to 120°F
  • Weight: under 1 oz
  • Color: black

2. Vortex Optics Defender Flip Cap — The Fold-Flat Cap

The Defender takes a different approach. Instead of a rigid collar in one exact size, it uses a flexible sleeve that stretches over the bell, and each size is specified as an outside-diameter range rather than a single number. The objective line runs from the O-24 at 28.25 to 31.25 mm up through the O-56 at 62 to 66 mm. The matching eyepiece cap, the E-10, fits eyepiece housings from 41.5 to 46 mm outside diameter. The Defender line is built for Vortex riflescopes, and the published diameter ranges are the figures to match against a measured bell.

The working end of the design is the stainless-steel snap-flat spring. Where many caps stand upright when open and snag on brush or clothing, the Defender folds back until it lies flat against the scope, completely out of the sight picture. The E-10 eyepiece cap adds three stop positions — vertical, which presents the inside of the cap toward the shooter, 45 degrees, and a full 90 degrees flat back. One fit exception is worth knowing: the E-10 does not fit the 1-inch-tube Viper models VPR-M-01BDC, VPR-M-04BDC, and VPR-M-03BDC.

Specs

  • Type: flip cap for objective or eyepiece, sold individually by size
  • Objective sizes (outside diameter): O-24 fits 28.25–31.25 mm; O-40 fits 45.5–48.5 mm; O-44 fits 49–53 mm; O-50 fits 55–59 mm; O-56 fits 62–66 mm
  • Eyepiece size: E-10 fits 41.5–46 mm outside diameter
  • Spring: stainless-steel snap-flat spring; cap folds flat against the scope
  • Stop positions (E-10): vertical, 45 degrees, and 90 degrees flat back
  • Fit exception: E-10 does not fit 1-inch-tube Viper models VPR-M-01BDC, VPR-M-04BDC, and VPR-M-03BDC
  • Construction: flexible sleeve with rigid cap

3. Monstrum Rubberized Flip-Up Rifle Scope Lens Cover — The Stretch-Fit Cap

Monstrum builds its flip-up cover around rubber rather than rigid polymer. The sleeve that grips the scope is rubberized and stretches, so each size tolerates a band of outside diameters instead of demanding one exact measurement, and the cap itself is polymer on a spring-loaded hinge. That makes this the forgiving option in the group: a bell that falls between the numbered sizes of a rigid-collar system, or an eyepiece with a slightly irregular housing, is more likely to seal under a sleeve that can give.

The range is sold in nine size steps. Objective covers span outside diameters from 26 to 66 mm, and eyepiece covers span 37 to 48 mm, with each cover sold individually — one for each end of the scope. The covers weigh about 27 grams each and are offered in black or flat dark earth.

Specs

  • Type: flip-up lens cover, sold individually (one cover per package)
  • Construction: rubberized sleeve with polymer cap
  • Mechanism: spring-loaded flip-up
  • Objective sizes: nine ranges covering 26–66 mm outside diameter
  • Eyepiece sizes: ranges covering 37–48 mm outside diameter
  • Weight: about 27 g per cover
  • Colors: black or flat dark earth

4. Butler Creek Bikini Rifle Scope Cover — The One-Piece Classic

The Bikini is the oldest design in this roundup and still one of the most practical for storage and transport. It is a single piece: two pliable rubber-like caps joined by stretch retainers. One cap pulls over the objective bell, the other over the eyepiece, and the tension between them holds both in place with a dust- and moisture-proof seal at each lens. There is no hinge to crack, no spring to weaken, and nothing to align — the cover fits riflescopes with objective bells up to 62 mm outside diameter, which spans the great majority of hunting scopes without any size chart at all.

That simplicity defines both its strength and its limit. A Bikini protects both lenses in the truck, in the case, and while the rifle is carried slung, and when it comes off it folds flat into a pocket. But it does come completely off. There is no way to shoot with it in place and no way to open just one end, so on a stand or in a blind it is a cover for the walk in and the wait before first light, not for the moment a deer steps out. Hunters who expect fast chances usually choose flip caps instead; hunters whose scopes live in cases between sits often need nothing more than this.

Specs

  • Type: one-piece bikini cover; two end caps joined by stretch retainers
  • Fit: riflescopes with objective bells up to 62 mm outside diameter
  • Model: 19000
  • Material: pliable rubber-like caps with elastic retainers
  • Seal: dust- and moisture-proof seal at both lenses
  • Use pattern: storage, transport, and carry; removes completely before shooting
  • Color: black

5. Allen Company Peak Neoprene Scope Cover, Large — The Full-Length Coat

The Peak protects a different thing than the caps above. A flip cap guards the glass; this neoprene coat wraps the whole scope — tube, turrets, and both housings — in a cushioned sleeve, which is the protection that matters in a soft case, a truck bed, or anywhere the scope itself takes knocks. The body is neoprene with a stretch poly jersey lining, so it slides over the scope without scratching the finish and absorbs the small impacts that chip turret edges and mark tubes.

Sizing is by scope length and maximum lens diameter rather than by bell measurement. The Large fits scopes up to 15 inches long with lenses up to 56 mm in diameter, which covers full-size hunting scopes including most 50 mm and 56 mm objective models; the Medium covers scopes up to 12 inches long with lenses up to 44 mm. A pull-tab opening peels the coat off in one motion, but like the Bikini, the Peak comes completely off before a shot, so its role is transport, storage, and camp. Tall target-style turrets can defeat the fit, since the sleeve is cut for hunting-scope profiles, so extended turrets should be checked against the cover’s stated limits first.

Specs

  • Type: full-length neoprene scope coat (slip-on sleeve)
  • Fit, Large: scopes up to 15 in long, lenses up to 56 mm diameter
  • Fit, Medium: scopes up to 12 in long, lenses up to 44 mm diameter
  • Material: neoprene body with stretch poly jersey lining
  • Opening: pull-tab for one-motion removal
  • Weight: about 0.33 lb (Large)
  • Color: black

How to Choose a Scope Cover

Measure the outside of the housing, not the lens. Put calipers across the widest part of the objective bell and across the eyepiece housing, and shop against those two numbers. The figure in a scope’s name — the 40 in a 3-9×40 — is the diameter of the glass itself. The bell around that glass is always wider, and by how much depends on the maker’s housing design, which is why two 40 mm scopes from different brands can take different cap sizes. Measure both ends separately: objective and eyepiece caps use different size runs, and a fast-focus eyepiece ring or an illumination knob can make the eyepiece’s widest point wider than its nominal housing.

Match the class to how the rifle is used. Flip caps are the field choice for hunting on foot or on stand, because they stay on the scope and open with a thumb when a shot appears. A bikini cover suits a scope that travels in a case and comes out for deliberate shots. A neoprene coat earns its place when the tube and turrets need padding — in a pack, a soft case, or a crowded gun safe.

Know the see-through option exists. A fourth style, the see-through cap, uses a clear or amber polymer lens in place of a solid lid, so a snap shot can be taken without opening anything. The trade is optical: looking through an extra layer of polymer gives a dimmer, less sharp image than bare glass, so the style suits close, fast chances, and most hunters still flip the cap open when time allows.

Be clear about what no cover can do. Every cover here seals the outside of the lenses against rain, dust, and brush contact. None of them prevents fogging from temperature change: carry a cold scope into a warm cabin or step from an air-conditioned truck into humid morning air, and moisture can form regardless of how tight the caps are. The practical response is to let the scope adjust gradually, not to shop for a tighter seal.

Check clearance before the hunt. An open flip cap needs room to fold without striking the barrel, the mount, or a sunshade — and a sunshade extends the front of the scope beyond the bell the cap was sized for. Confirm at home that the cap opens fully on the mounted rifle.

FAQ

How do I measure my scope for a flip cap?
Measure the outside diameter of the objective bell and of the eyepiece housing with calipers, then match each number to the maker’s size chart for that end. The two ends use different size runs, so a scope needs two measurements and usually two different sizes. If a measurement falls between two rigid-collar sizes, a flexible-collar or stretch-sleeve design is built to absorb exactly that gap.

My scope is a 3-9×40. Which cap size do I need?
The 40 refers to the objective lens diameter in millimeters, not the size of the housing around it. The bell’s outside diameter on a 3-9×40 is larger than 40 mm and varies by brand and model — commonly somewhere in the mid-40s to about 50 mm. Measure the bell itself: a bell at 45.7 to 46.7 mm, for example, is the fit window for the Multiflex size 25-26-27 above, while a bell at 45.5 to 48.5 mm falls in the Vortex O-40 range. Guessing from the scope’s name alone is how the wrong size gets ordered.

Will a scope cover stop my lenses from fogging?
No. Covers block rain, dust, and brush from reaching the outside of the glass. Fogging from temperature change is a different mechanism — moisture condensing as a cold scope meets warm, humid air — and it happens with or without a cover fitted. Letting the scope warm or cool gradually before uncovering the glass is the workable approach.

Can you shoot through a see-through scope cap?
Yes — that is what the style is designed for. See-through caps use a clear or amber polymer window so the scope can be used in an emergency without opening the cover. The image through the window is dimmer and less crisp than through the scope’s own glass alone, so the window is a fallback for a fast, close opportunity, not a substitute for opening the cap when there is time.

Conclusion

The right cover is the one whose stated measurements match a caliper reading from the scope it will live on. For an exact-fit flip cap on a mid-size bell, the Butler Creek Multiflex in size 25-26-27 is the straightforward choice, and its flexible collar forgives small differences between scope models. The Vortex Defender answers with a fold-flat spring and a wide ladder of size ranges, while the Monstrum’s rubberized sleeve offers the most tolerant fit of the three flip designs. For protection away from the shot, the Butler Creek Bikini covers both lenses with one simple piece for storage and transport, and the Allen Peak wraps the entire scope in neoprene when the tube and turrets need shelter as much as the glass. Measure both ends, pick the class that matches how the rifle is carried, and the cover will do its unglamorous job for seasons.

C
Camping Spots Editorial Team
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Scope Covers and Lens Caps for Hunting…Check price on Amazon

More from Amazon

Programs that pair well with the guide above. Offers and eligibility are set by Amazon and may change.

Amazon Prime

Free shipping on eligible items, Prime Video and more. Eligible new members can start with a free trial.

Start a Prime free trial
Prime for Young Adults

A Prime membership for ages 18-24 with a trial period. Eligibility is set by Amazon.

See Prime for Young Adults
Audible

Audiobooks and podcasts to listen to on the go. Eligible new members can start with a free trial.

Try Audible free
Amazon Music Unlimited

Ad-free music streaming. Eligible new subscribers can start with a free trial.

Try Music Unlimited free

As an Amazon Associate we earn from qualifying purchases.